- 您现在的位置：买卖IC网 > Sheet目录885 > SSQE48T10033-PABNG (Power-One)DC/DC SIXTEENTH BRICK
SSQE48T10033 DC-DC Converter Data Sheet
36-75 VDC Input; 3.3 VDC, 10 A Output
by the same percentage to ensure the converter’s
actual output power remains at or below the
maximum allowable output power.
R T ? DECR ?
where,
511
| Δ |
? 10.22
[k ? ]
Output Voltage Adjust /TRIM (Pin 6)
The output voltage can be adjusted up 10% or down
20%. Trim up to 10% is guaranteed only at Vin ≥
37.5V, and it is approximately 8% to 10% at Vin =
36V.
The TRIM pin should be left open if trimming is not
being used. To minimize noise pickup, a 0.1 μF
capacitor is connected internally between the TRIM
and SENSE(-) pins.
R T-DECR = Required value of trim-down resistor [k ? ]
and Δ is defined above.
Note:
The above equations for calculation of trim resistor values match
those typically used in conventional industry-standard quarter-
bricks, eighth-bricks and sixteenth-bricks.
SSQE48 Converter
To increase the output voltage, refer to Fig. C. A trim
resistor, RT-INCR, should be connected between the
TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of:
Vin
Vin (+)
ON/OFF
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-DECR
Rload
R T ? INCR ?
5.11(100 ? Δ )V O ? NOM ? 626
1.225 Δ
? 10.22
[k ? ],
Vin (-)
Vout (-)
Fig. D: Configuration for decreasing output voltage.
Δ ?
(V O - REQ ? V O - NOM )
where,
R T ? INCR ? Required value of trim-up resistor [k ? ]
V O ? NOM ? Nominal value of output voltage [V]
X 100 [%]
V O - NOM
V O ? REQ ? Desired (trimmed) output voltage [V].
Trimming/sensing beyond 110% of the rated output
voltage is not an acceptable design practice, as this
condition could cause unwanted triggering of the
output overvoltage protection (OVP) circuit. The
designer should ensure that the difference between
the voltages across the converter’s output pins and
its sense pins does not exceed 10% of V OUT (nom),
or:
[V OUT ( ? ) ? V OUT ( ? )] ? [V SENSE ( ? ) ? V SENSE ( ? )] ? V O - NOM X 10% [V]
When trimming up, care must be taken not to exceed
the converter‘s maximum allowable output power.
See the previous section for a complete discussion
of this requirement.
This equation is applicable for any condition of
output sensing and/or output trim.
Vin (+)
SSQE48 Converter
(Top View)
Vout (+)
SENSE (+)
R T-INCR
Vin
ON/OFF
TRIM
Rload
SENSE (-)
Vin (-)
Vout (-)
Fig. C: Configuration for increasing output voltage.
To decrease the output voltage (Fig. D), a trim
resistor, R T-DECR , should be connected between the
TRIM (Pin 6) and SENSE(-) (Pin 5), with a value of:
ZD-01889 Rev. 1.1, 17-Nov-09
www.power-one.com
Page 5 of 13
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SSQE48T20033-NABNG
CONVERTER DC-DC 3.3V 20A
SSQE48T20033-PABNG
DC/DC SIXTEENTH BRICK
SSQE48T25015-PABNG
DC/DC SIXTEENTH BRICK
SSQE48T25018-PABNG
DC/DC SIXTEENTH BRICK
SSQE48T25025-PABNG
DC/DC SIXTEENTH BRICK
SSQL48T20033-NAABG
CONV DC-DC 3.3V 20A 1/16 BRICK
ST5ER504
TRIMMER 500K OHM 0.25W SMD
ST7ETB503
TRIMMER 50K OHM 0.25W SMD
相关代理商/技术参数
SSQE48T13050-NAA0G
制造商:Power-One 功能描述:DC/DC CONVERTER 5V 65W
SSQE48T13050-NAANG
制造商:Power-One 功能描述:DCDC - Bulk
SSQE48T13050-NAB0G
功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T13050NABNG
功能描述:DC/DC转换器 65W 5Vout 13A 36-75Vin PIN=0.145" RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T13050-NABNG
制造商:Power-One 功能描述:Module DC-DC 1-OUT 5V 13A 8-Pin 1/16-Brick
SSQE48T13050-NAC0G
制造商:Power-One 功能描述:- Bulk
SSQE48T13050-NACNG
功能描述:DC/DC转换器 65W 5V out 13A PIN LENGTH 0.110 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
SSQE48T13050-PAB0G
制造商:Power-One 功能描述:Module DC-DC 1-OUT 5V 13A 8-Pin 1/16-Brick